C0031 on Jeep: How to Diagnose & Fix
Left Front Wheel Speed Sensor Circuit
1 Jeep model · 1 documented issue
C0031 on Jeep by model: symptoms, diagnosis and fix
On 2019 model-year Jeep Grand Cherokee (WK) vehicles, an ABS warning that diagnosis traces to a wheel-speed circuit may be caused by an incompletely latched connector, water intrusion and corroded connector pins, rust or contamination at the sensor and tone wheel, or a faulty sensor. FCA warns that replacing a good sensor while leaving a damaged harness in place can cause the concern to return. The previous card incorrectly generalized this condition across 2011-2021 vehicles, named the right-front sensor as a common cause, listed unsupported DTCs and symptoms, and presented three universal repair parts.
Common Symptoms
- ABS warning light illuminated
How to Fix
Read the ABS module and compare individual wheel-speed live data to isolate the affected circuit. Inspect the connector latch, pins, and harness for water intrusion, corrosion, routing problems, or damage; replace a damaged harness rather than the sensor. Inspect and clean the sensor mounting area and tone wheel, reinstall the sensor, and retest the signal. Replace the sensor only when electrical and signal testing confirms it is faulty, then clear faults and verify normal wheel-speed data on a road test. Confirm any replacement by VIN and installed equipment before ordering.
What you need to fix it
Only diagnosis- and fitment-reviewed repair parts are linked here.
- Front ABS wheel speed sensor (vehicles WITHOUT adaptive cruise control) - fits left or rightOEM68250893AACross-refStandard Motor Products ALS2902, HHKSC 2-pc front set (Amazon B0G9F47YQ2), Mopar supersession 68569551AA$39–$55
Only buy AFTER the documented diagnosis: compare live wheel-speed data, inspect the connector latch/pins and harness for water intrusion or corrosion, and clean the sensor seat and tone wheel. FCA says a damaged harness must be replaced …
- Rear ABS wheel speed sensor - fits left or rightOEM5154230AFCross-refStandard Motor Products ALS2064, A-Premium rear sensor (Amazon B097XTJY53), Mopar 5154230AA/AB/AC/AD/AE (earlier revisions)$57–$82
Only buy after the documented diagnosis isolates a rear circuit and confirms the sensor (not the harness or connector) is at fault. Confirm by VIN before orderi
As an Amazon Associate, we earn from qualifying purchases; other part links may also earn au7o a commission. Confirm fitment by VIN before buying.
Owner tips & cautions
- WarningDo not order a wheel-speed sensor from the warning light alone. FCA specifically documents corroded connector pins and tone-wheel rust that can make a good sensor appear faulty.
- TipAsk the shop to record the ABS fault and individual wheel-speed live data, then document the connector, harness, and tone-wheel inspection before authorizing a part.
- WarningThe corrected scope is 2019 model year only. The prior 2011-2021 range and right-front-specific claim were removed because the reviewed FCA evidence does not establish them.
Sources for this issue (2)
C0031 code reference
General diagnostic-code context. The code alone does not confirm a cause for your vehicle; use the applicable issue card and its sources.
Frequently asked questions
What does C0031 mean on a Jeep?
C0031 stands for "Left Front Wheel Speed Sensor Circuit." C0031 is a chassis/brake code indicating a fault in the left front wheel speed sensor circuit. The ABS module relies on this sensor to measure individual wheel rotation for anti-lock braking, traction control, and stability control; when it detects an open, short, or implausible signal it sets this code. The ABS, traction control, and stability control warning lights typically illuminate and those systems may be temporarily disabled, while normal (non-ABS) braking usually still works. On Jeep it is documented across 1 model: Grand Cherokee.
What are the most common causes of C0031?
The most common causes of C0031 are: Failed left front wheel speed sensor, Damaged sensor wiring or chafed harness, Corroded or loose sensor connector, Damaged or contaminated tone/reluctor ring (metal debris, rust), Excessive sensor-to-ring air gap or wheel bearing play, ABS control module fault. The specific cause varies by vehicle.
How much does it cost to fix C0031 on a Jeep?
Repair costs vary widely with the root cause and Jeep model; each issue on this page carries its own estimate where one is published.
Looking for C0031 on a different make?
View C0031 across all makes →Content compiled with AI assistance using NHTSA complaints, TSBs, and owner reports. May contain errors. Always verify with your vehicle's service manual.