U1028 on 2022-2024 Ford Maverick — Invalid or Missing Data for Primary ID (Manufacturer-Specific)
1 vehicles · 1 makes
How to diagnose and fix U1028: most-reported vehicles
Ranked by owner reports. Each card gives the symptoms, how to confirm the cause, the fix, parts and sources for that vehicle.
Ford Maverick · 2022–2024
On affected 2022-2024 Maverick Hybrid trucks, a recent update to the Hybrid Powertrain Control Module (HPCM) software calibration may result in a forced neutral condition while driving, causing the vehicle to coast to a stop and automatically shift to Park, along with a wrench light, multiple warning messages, and an audible chime. After shifting back into Drive the vehicle enters a limp home mode with limited torque at speeds up to 30 mph. Ford's powertrain controls team determined that new Hybrid Transmission Internal Park Module (HTIPM) software released for use in service in January 2024 can result in DTCs U1010 and U1011 shortly after installation, and Ford was aware of 315 warranty claims in North America as of April 15, 2024. The recall covers approximately 8,727 vehicles (Maverick population ~8,369).
Common Symptoms
- Vehicle suddenly shifts to Neutral while driving
- Auto-shifts to Park as truck coasts to a stop
- Wrench warning light illuminated
- Audible chime and multiple IPC warning messages
- Limp home mode limited to ~30 mph after restart
- Truck strands driver and may require tow
How to Fix
Dealers will reflash the HPCM/PCM with corrected software free of charge under recall 24S33. If the remedy software for Safety Recall 24S33 was not installed correctly during a prior dealership visit, the underlying forced-neutral condition may still exist, so verify the calibration ID on the OASIS report — a follow-up recall (25V133 / 25S16) was issued in April 2025 for incorrect reflashes, and a further expansion was issued with owner notification letters mailed February 12, 2026. Primary confirmed DTCs in Ford's Part 573 report are U1010 and U1011; owners have additionally reported U1028, U0418, U0401, and U0131 on basic OBD readers, all of which should clear after the corrected update. Repair is performed at no cost and takes less than one hour.
Find a Ford dealer
Choose to share your location for this search, or enter an area below. Your search location is sent to Google to find dealers.
Open Ford dealer map in Google Maps ↗Call to confirm they service Ford vehicles and check your VIN, recall eligibility, parts availability, and appointment options.
Sources for this issue (2)
Find U1028 by make
Browse every documented model and issue for your make.
U1028 code reference
General diagnostic-code context. The code alone does not confirm a cause for your vehicle; use the applicable issue card and its sources.
Frequently asked questions
What does U1028 mean?
U1028 stands for "Invalid or Missing Data for Primary ID (Manufacturer-Specific)." U1028 is a manufacturer-specific communication code generally meaning a module received invalid or missing data tied to a 'primary identification' message on the data bus. In practice this points to a problem in how modules identify or talk to each other across the network rather than a single failed component. The symptoms depend on which module raised the code and what data it was waiting on.
What are the most common causes of U1028?
The most common causes of U1028 are: Data bus wiring damage (open, short, chafe), Loose or corroded module connectors, Faulty control module or gateway, Poor ground / high-resistance ground, Low or unstable system voltage, Module not properly configured/programmed after replacement, Corrosion from water intrusion. The specific cause varies by vehicle.
How much does it cost to fix U1028?
Repair costs vary widely depending on the root cause and vehicle.
Which vehicles are affected by U1028?
Au7o has documented U1028 across 1 vehicle models from 1 manufacturers: Ford.
Content compiled with AI assistance using NHTSA complaints, TSBs, and owner reports. May contain errors. Always verify with your vehicle's service manual.