P0305 on Audi: How to Diagnose & Fix
Cylinder 5 Misfire Detected
15 Audi models · 17 documented issues · $120-$2,000 repair
P0305 on Audi by model: symptoms, diagnosis and fix
The RS7's 4.0T V8 is a direct-injection engine. Fuel is sprayed straight into the cylinders, so it never passes over the intake valves to wash them, and carbon deposits build up on the valve backs over time. As the deposits grow they restrict airflow and upset the air-fuel mixture. Audi's general fuel-quality bulletin (TSB 2014753, covering all 2000-2019 Audi models) lists the results of deposits on intake valves, injectors and combustion chambers: rough running after a cold start, rough idle, hesitation, reduced performance and poorer fuel economy. In more severe cases the check-engine light comes on with misfire or lean-mixture codes. The same bulletin names low-detergent or contaminated fuel as a contributing cause.
Common Symptoms
- Rough idle
- Rough running or misfires after a cold start
- Power loss at high RPM
- Hesitation under load
- Check-engine light with a misfire or lean-mixture code (e.g. P0300, P0171/P0174)
- Turbo lag increase
How to Fix
1. Check first: read the stored fault codes. Codes from Audi's bulletin TSB 2014753 that point to this problem include misfire codes (P0300 and P0301-P0308) and lean-mixture codes (P0171/P0174). Rule out simpler misfire causes such as spark plugs and coils. If deposits are still suspected, have a professional inspect the intake valves to confirm buildup before paying for a cleaning. 2. Fuel additives will not fix valve deposits on this engine. TSB 2014753 says Audi's additive (G 001770A2) cleans injectors and combustion chambers, and intake valves only on port-injected (MPI) engines. For intake-valve deposits on direct-injection (FSI/TFSI) engines it refers technicians to a separate bulletin, TSB 2019948. 3. The fix: mechanical cleaning of the intake valves, most often walnut blasting. Crushed walnut shells are blasted onto the valves to remove the carbon and restore airflow. 4. Prevention: Audi's bulletin recommends using TOP TIER detergent gasoline and avoiding contaminated fuel. One European specialist guide quotes a cleaning interval of about 30,000-50,000 miles depending on driving conditions. Use that as a guide only and clean when symptoms or an inspection show deposits. 5. Coverage: TSB 2014753 allows warranty diagnosis claims up to 48 months/50,000 miles. It says the additive is not reimbursed under warranty, and the bulletin is informational only for cars outside warranty. Ask an Audi dealer whether a cleaning is covered on your car. No recall covers this condition.
What you need to diagnose it
The repair instructions explicitly call for reading stored codes. Use a scanner that can read the named code families before choosing a repair.The recommended scanner supports these code families; confirm your exact year, model and module coverage before buying.
ANCEL AD310 Classic OBD-II Scanner
Read & clear engine (P) codes
$20–$40View
As an Amazon Associate, we earn from qualifying purchases. Prices are approximate and may vary.
Reading and clearing the code is DIY work. Module replacement or reprogramming is not — most modules are VIN-programmed, so a new one does nothing until a shop codes it to your car. Check for an open recall or service bulletin before buying anything.
Call to confirm they can assess your vehicle and perform the stated work. Search results do not confirm qualification, eligibility or coverage.
Sources for this issue (2)
The S5 suffers from carbon deposits on the intake valves, a problem common to all Audi direct-injected engines. The performance-oriented tuning makes power loss from carbon more noticeable than in base models.
Common Symptoms
- Rough idle
- Power loss
- Cold start misfires
- Hesitation under load
- Check engine light
- Poor throttle response
How to Fix
Walnut blast intake valves every 40,000-60,000 miles. Install oil catch can to reduce oil vapor reaching valves.
Sources for this issue (2)
The 4.0T twin-turbo V8 in RS6, RS7, and RS Q8 suffers from severe carbon buildup on intake valves due to direct injection. The high-performance nature and twin-turbo setup means carbon accumulates faster than in lower-output engines. Over 60,000 miles, carbon restricts airflow causing rough idle, misfires, and power loss. The V8 configuration requires removing both intake manifolds, making walnut blasting more expensive ($1,200-$2,000) than 4-cylinder engines. Failure to clean can cause valve damage requiring expensive cylinder head work on the $120,000+ RS models.
Common Symptoms
- Rough idle
- Hesitation on acceleration
- Power loss
- Poor fuel economy
- Check engine light with misfire codes
- Engine runs rough when cold
How to Fix
WALNUT BLASTING: Remove both intake manifolds and blast walnut shells through all intake ports ($1,200-$2,000 for the V8). For the confirmed cold-start misfire deposit condition, Audi TSB 2075530/1 directs removing the intake manifold or compressor and walnut-blasting the inlet valves and ports with the cylinder head installed; the bulletin does not set a cleaning interval. Confirm heavy deposits by borescope before paying for cleaning. PREVENTION (owner-community practice, not an Audi instruction): some owners fit an oil catch can to reduce PCV oil vapour reaching the valves, and keep oil changes on time; results vary, and a catch can may affect warranty or emissions compliance. Fuel or oil additives cannot reach the intake valves on a direct-injection engine and are not a remedy.
Sources for this issue (2)
The direct-injection engines in the A5 (2.0 TFSI and 3.2L V6) suffer from severe carbon buildup on intake valves. In direct-injection engines, fuel sprays directly into the cylinder, bypassing the intake valves. This means intake valves are only exposed to oil vapors from the PCV system, which bake onto the valve backs as hard carbon deposits. Over 60,000-100,000 miles, carbon restricts airflow, causing rough idle, misfires, hesitation, and power loss. In severe cases, carbon deposits prevent valves from seating properly, causing compression loss and valve damage. The only effective fix is walnut blasting—blasting crushed walnut shells through the intake to remove carbon. A5OC forums recommend this as preventive maintenance every 60,000 miles.
Common Symptoms
- Rough or unstable idle (engine shakes at stoplights)
- Hesitation or stumbling on acceleration
- Reduced power and sluggish throttle response
- Poor fuel economy (2-4 MPG drop)
- Check engine light with misfire codes (P0300-P0306)
- Engine runs rough when cold, smooths out when warm
- Hard starting or extended cranking
How to Fix
Walnut blasting: remove the intake manifold and blast crushed walnut shells through the intake ports to remove carbon ($700-$1,200). Requires specialized equipment - DIY not recommended unless experienced. Dealers charge $1,200-$1,800; independent Audi shops charge less. Confirm heavy deposits by borescope before paying for cleaning; there is no manufacturer-set cleaning interval. Prevention (owner-community practice, not an Audi instruction): some owners fit an oil catch can to reduce PCV oil vapour reaching the valves, and keep oil changes on time; results vary, and a catch can may affect warranty or emissions compliance. Fuel or oil additives cannot reach the intake valves on a direct-injection engine and are not a remedy.
Sources for this issue (2)
Audi states that contaminated gasoline, or gasoline low in deposit-control additives, can build deposits on the intake valves, intake manifold, fuel injectors and combustion chambers. Results can include rough running after a cold start, long cranking, hesitation, rough idle, reduced performance, poor fuel economy, and a check-engine light with misfire, lean-fuel-system or air/fuel-ratio-imbalance codes. Applies to: All Audi vehicles from model years 2000–2025 (bulletin 2014753/13, December 5, 2024), which includes the 2017–2020 and 2022–2025 Audi RS 3 with the 2.5 TFSI five-cylinder. It is a diagnosis guide, not evidence that every RS 3 develops deposits.
Common Symptoms
- Rough running after a cold start
- Extended cranking
- Hesitation or rough idle
- Reduced performance or poor fuel economy
- Check-engine light with the bulletin-listed misfire, lean-system or air/fuel-ratio codes
How to Fix
Have a dealer read the fault memory and consider the fuel source; the bulletin is a fuel-quality diagnosis guide. If contaminated fuel is suspected (unusual color or odor, water, sediment, cloudiness or separation after settling), the bulletin advises changing the fuel source. If low-additive fuel is suspected, it recommends TOP TIER Detergent Gasoline. Audi gasoline additive G 001770A2, mixed into a full tank, can be used to remove deposits from injectors and combustion chambers; intake-valve deposits on FSI direct-injection engines are handled under a separate Audi bulletin, 2019948. The bulletin is informational only, is not applicable to any Audi warranty, and the additive is not reimbursed. This is not a recall or a promise of free repair.
Call to confirm they can assess your vehicle and perform the stated work. Search results do not confirm qualification, eligibility or coverage.
Sources for this issue (1)
For a 2019-2021 Audi A6 equipped with the 3.0L TFSI engine, the malfunction indicator lamp may illuminate with P0300 and one or more cylinder-specific P0301-P0306 codes. Audi's service information identifies an applicable ECM software-calibration condition and publishes model-year-specific software levels. Misfire codes alone do not prove intake-valve carbon buildup. Carbon cleaning or parts replacement requires separate physical diagnosis if the misfire remains after the software level and other common causes are checked.
Common Symptoms
- Malfunction indicator lamp or check-engine light illuminated
- P0300 random/multiple-cylinder misfire stored
- One or more P0301-P0306 cylinder-specific misfire codes stored
How to Fix
Record every stored DTC and freeze-frame before clearing faults. Confirm that the vehicle is a 2019-2021 A6 with the 3.0L engine, then have an Audi dealer or qualified VAG specialist compare the ECM J623 part number and software version with Audi's bulletin and perform the specified Software Version Management update when applicable. For MY2019 the bulletin lists 4K0907559A version 0007 updating to 0008 with SVM action 01A255; MY2020 lists 4K0907559D version 0002 updating to 0003; MY2021 lists 4K0907559K versions 0001-0002 updating to 0004. Recheck for misfires after the update. If faults persist, diagnose ignition, plugs, injectors, fuel quality, air leaks, compression, and only then inspect the intake valves before authorizing cleaning. Do not buy a catch can, cleaner, ignition part, or walnut-blasting service solely from P0300-P0306.
Call to confirm they can assess your vehicle and perform the stated work. Search results do not confirm qualification, eligibility or coverage.
Owner tips & cautions
- TipSave the complete scan and freeze-frame before an update or repair. The cylinder pattern and operating conditions are useful if the misfire remains.
- WarningP0300-P0306 do not identify carbon buildup by themselves. Verify the Audi software level and diagnose the remaining possible causes before paying for walnut blasting or ordering parts.
- WarningThe published fix is software, so ShowMeTheParts cannot validate it and no retail product link belongs on this record.
Sources for this issue (2)
P0305 code reference
General diagnostic-code context. The code alone does not confirm a cause for your vehicle; use the applicable issue card and its sources.
Frequently asked questions
What does P0305 mean on a Audi?
P0305 stands for "Cylinder 5 Misfire Detected." This code means the engine control module detected a misfire on cylinder number 5, meaning that cylinder is not burning its air-fuel mixture properly on some combustion cycles. The computer senses misfires by watching for tiny fluctuations in crankshaft speed each time a cylinder fails to fire correctly. A misfire wastes fuel, can make the engine run rough or shake, and dumps unburned fuel into the exhaust, which can overheat and damage the catalytic converter. It generally points to a problem with spark, fuel delivery, or compression specifically affecting cylinder 5. On Audi it is documented across 15 models: RS7, S5, RS6, A5, RS3, A6, R8, A7, Q8, S6, SQ5, S7, Q5, A8, RS4.
What are the most common causes of P0305?
The most common causes of P0305 are: Worn or fouled spark plug on cylinder 5, Failed ignition coil or coil pack for cylinder 5, Faulty or clogged fuel injector on cylinder 5, Vacuum or intake air leak affecting that cylinder, Bad spark plug wire or boot (on applicable engines), Low compression from worn rings, valves, or head gasket, Carbon buildup or sticking valve on cylinder 5, Lean or rich fuel condition affecting the cylinder. The specific cause varies by vehicle.
How much does it cost to fix P0305 on a Audi?
Published repair estimates on Audi range from $120 to $2,000 depending on the model and root cause. If an issue mentions a recall or campaign, check your VIN with the manufacturer or NHTSA and confirm eligibility and coverage with a dealer.
Looking for P0305 on a different make?
View P0305 across all makes →Join 700+ subscribers following Au7o for vehicle insights and updates.
Content compiled with AI assistance using NHTSA complaints, TSBs, and owner reports. May contain errors. Always verify with your vehicle's service manual.