Au7o mascotAu7o
Known IssuesTest Hub demo
  1. Au7o
  2. /
  3. Known Issues
  4. /
  5. Nissan
  6. /
  7. Versa
Nissan · Known Issues

2014 Nissan Versa Problems: 13 Known Issues

2014 model year · 4,180+ owner reports · Updated September 2026

Share:@au7o.io

2014 · All trims · All engines

Choose the year and equipment for your written issues and visual request.

No email neededHow interest is saved

Interest applies to the selected vehicle and configuration; it is not a reservation. Voting stores a first-party identifier for up to 180 days to prevent repeat votes. No account or email is needed. Clearing cookies or using another device may count separately. Privacy

Visual coming soon

Your interest helps us choose what to build next.

Visual Known Issues · Coming soon

Known IssuesMotorcycle IssuesDTC LookupDrivePricingAboutTermsPrivacyCookiesConsentData rightsCopyrightFeedback
Share:@au7o.io

Vehicle data and repair guidance on this site are compiled with AI assistance and may contain errors. Always verify with your service manual or a qualified mechanic.

Data protection representation

DataRep representative in the United KingdomDataRep representative in the European Union
Au7o · 2026
Built for DIY mechanics. Privacy-first.
Explore free Hub demo

$4.99/month plus taxes at launch · No payment today

Preview the XT6 example
Issue summary

According to Au7o's analysis of 4,180+ owner reports, the 2014 Nissan Versa has 13 documented known issues, with 4 rated critical. The most serious are CVT Transmission Failure (Jatco CVT7/JF015E) ($300-$4,500 repair), Rear Coil Spring Fracture and Corrosion ($200-$500 repair), Brake Master Cylinder Internal Seal Bypass — Pedal Sinks to the Floor With No External Leak ($250-$700 repair) and Passenger Occupant Classification Sensor (OCS) Mat Failure — Passenger Airbag Stays Disabled ($150-$1,200 repair). The most commonly reported issue is CVT Transmission Failure (Jatco CVT7/JF015E) with 3,500 owner reports. Across all issues with published estimates, repair costs range from $10 to $4,500. DIY maintenance guides at au7o.io.

In This Article

  • Versa Suspension3
  • Versa Transmission1
  • Versa Brakes1
  • Versa Safety/Recalls1
  • Versa Engine4
  • Versa Electrical1
  • Versa HVAC1
  • Versa Fuel System1
  • Recalls5
  • FAQ
Get Started
Back to top

In This Article

  • Suspension3
  • Transmission1
  • Brakes1
  • Safety/Recalls1
  • Engine4
  • Electrical1
  • HVAC1
  • Fuel System1
  • Recalls5
  • FAQ

All 13 Known Issues

NHTSA Recalls5 recalls

AIR BAGS:FRONTAL:DRIVER SIDE:INFLATOR MODULE

Nissan North America, Inc. (Nissan) is recalling certain 2024 Titan, Frontier, Infiniti QX60, Pathfinder, 2023-2024 Sentra, Versa, Kicks, Infiniti QX50, and 2023 Rogue vehicles. Due to a manufacturing issue, the driver's air bag inflator may absorb moisture, and cause the air bag to deploy improperly.

Campaign #24V15400027/02/2024

EXTERIOR LIGHTING:TURN SIGNAL:BULBS

Nissan North America, Inc. (Nissan) is recalling certain 2020-2021 Titan, Titan XD, and Versa vehicles. The front right and/or left turn signal bulb can crack and fail to illuminate.

Campaign #21V47100023/06/2021

FUEL SYSTEM, GASOLINE:STORAGE:TANK ASSEMBLY

Nissan North America, Inc. (Nissan) is recalling certain 2020 Versa vehicles. Due to a manufacturing issue, the fuel tank wall thickness may be insufficient, potentially causing a small hole in the tank seam area.

Campaign #20V11200026/02/2020
🔧
A mechanic who knows YOUR exact car
Answers tuned to your year, make, model & trim — not generic advice. Save your garage so it always has the right context.
Get ahead of Nissan Versa problems — free
Leave your email and we'll alert you the moment there's a new recall or known issue for your Nissan Versa. Free, no account needed.

Don't see your problem? Describe your symptoms to get a diagnosis, or .

Other Nissan Models

Nissan Rogue46Nissan Altima41Nissan Sentra32Nissan Frontier30Nissan Pathfinder24Nissan Murano22

Frequently Asked Questions

What are the most common Nissan Versa problems?

According to Au7o's analysis of 4,180+ owner reports, the 2014 Nissan Versa has 13 documented issues. The most frequently reported are: CVT Transmission Failure (Jatco CVT7/JF015E), Rear Coil Spring Fracture and Corrosion, Brake Master Cylinder Internal Seal Bypass — Pedal Sinks to the Floor With No External Leak. Of these, 4 are rated critical and should be addressed promptly.

Is the Nissan Versa reliable?

The 2014 Nissan Versa has 13 known issues documented across 4,180+ owner reports. 4 issues are rated critical: CVT Transmission Failure (Jatco CVT7/JF015E) and Rear Coil Spring Fracture and Corrosion and Brake Master Cylinder Internal Seal Bypass — Pedal Sinks to the Floor With No External Leak and Passenger Occupant Classification Sensor (OCS) Mat Failure — Passenger Airbag Stays Disabled. Prospective buyers should inspect for these issues and factor potential repair costs into their purchase decision. Regular maintenance following the manufacturer's schedule helps prevent many common problems.

How much does it cost to fix common Nissan Versa problems?

Repair costs for known Nissan Versa issues range from $10 to $4,500, depending on the specific problem and whether you choose DIY or professional repair. The most critical issue, CVT Transmission Failure (Jatco CVT7/JF015E), typically costs $300-$4,500 to repair. Au7o provides step-by-step DIY maintenance guides that can help reduce repair costs.

What is the 2012-2021 Nissan Versa CVT Transmission Failure (Jatco CVT7/JF015E)?

The 2012-2021 Versa CVT (Jatco JF015E) is one of the most failure-prone transmissions in Nissan's lineup. The combination of a budget vehicle with heavy use leads to premature CVT failure, often before 100,000 miles. Nissan extended the CVT warranty on 2012-2017 models to 10 year… Repairs typically run $300-$4,500. Severity: high.

What is the 2012-2019 Nissan Versa Rear Coil Spring Fracture and Corrosion?

The 2012-2019 Versa rear coil springs are prone to fracture, particularly in cold/salt-belt climates. The springs corrode and break, potentially puncturing tires or causing suspension collapse. Nissan issued Recall R1713 (NHTSA 17V-633) for 2012 Versa Note models and extended cov… Repairs typically run $200-$500. Severity: high.

Content on this page was compiled with AI assistance using NHTSA complaints, TSBs, owner reports, and public automotive data. While we strive for accuracy, this information may contain errors. Always verify repair procedures and specifications with your vehicle's service manual or a qualified mechanic.

Data sourced from 4,180+ owner reports, NHTSA recalls, TSBs, and automotive forums.

Filter:
ALL YEARS202420232022202120202019201820172016201520142013201220112010200920082007
Community reported
680 owners

On the 2012-2019 Nissan Versa, the 2012-2019 Versa rear coil springs are prone to fracture, particularly in cold/salt-belt climates. The springs corrode and break, potentially puncturing tires or causing suspension collapse. Nissan issued Recall R1713 (NHTSA 17V-633) for 2012 Versa Note models and extended coverage on other years.

Common Symptoms

  • Clunking from rear suspension
  • Vehicle sitting lower on one side
  • Visible broken spring
  • Tire damage from spring contact
  • Popping noise over bumps

How to Fix

Inspect rear coil springs for corrosion and cracks. Check if your VIN is covered under Recall R1713. Replace both rear springs simultaneously (part# 55020-3VY0A). Apply rust inhibitor to new springs. Cost: $200-500 for both springs installed.

Find a Nissan dealer

Choose to share your location for this search, or enter an area below. Your search location is sent to Google to find dealers.

Open Nissan dealer map in Google Maps ↗

Call to confirm they service Nissan vehicles and check your VIN, recall eligibility, parts availability, and appointment options.

Typical repair cost:$200 - $500

Research This Issue

Based on 680 owner reports

GoogleRedditYouTubeNHTSA
Community Reported
High Confidence680 owner reportsLast reported by owners Feb 2026Reviewed Feb 2026

On the 2007-2024 Nissan Versa, the Versa's rear suspension is a simple torsion beam with non-driven hubs, and on sedan and Versa Note models the rear bearing is a press-in double-row unit rather than a bolt-on hub cartridge. These are a well-documented wear item on the platform, typically surfacing between roughly 70,000 and 120,000 miles and much earlier in salt-belt states where water intrudes past the seal and rusts the races. The failure announces itself as a humming or roaring that rises with road speed and changes character when the car is loaded in a corner — louder turning one way, quieter the other. Because the rear is non-driven and unloaded, owners frequently mistake the noise for tire wear and replace tires first with no improvement. Fronts on the Versa are a bolt-on hub assembly and are far simpler; the rear is the one that catches people out, because a press and a proper knuckle/beam setup are required, which turns a modest part cost into a real labor bill.

Common Symptoms

  • Humming or roaring that increases with vehicle speed
  • Noise volume changes when steering left versus right
  • Growling from the rear of the car that owners mistake for tire noise
  • Play felt at the wheel when rocked at 12 and 6 o'clock
  • Noise unaffected by braking or by shifting gears

How to Fix

Confirm by road test rather than by jacking the car up — an unloaded rear bearing often feels fine by hand while roaring under load. Note whether the hum grows turning left (blame the right bearing) or turning right (blame the left). Rotate the tires first to rule out cupped/feathered tread, which mimics the noise exactly. Front bearings are a bolt-on hub assembly and are DIY-friendly. Rear press-in bearings require a hydraulic press and correct seating, so this is normally a shop job; do them in pairs if both are near the same mileage. Use a premium bearing brand (SKF, Timken, FAG, NTN) — owners report short lives from budget units.

Typical repair cost:$180 - $650

Research This Issue

GoogleRedditYouTubeNHTSA
Community Reported
Medium ConfidenceVerifiedReviewed Aug 2026

On the 2012-2022 Nissan Versa, the second and third generation Versa develops noise from the front strut mount bearings, producing a creaking, popping, or groaning sound when turning the steering wheel, especially at low speeds and in parking lots. The strut mount bearing (also called a strut plate bearing) wears out due to the lightweight suspension design and road salt exposure. The noise is often mistaken for power steering issues.

Common Symptoms

  • Creaking or popping when turning at low speed
  • Groaning noise in parking lots
  • Clunking over bumps from front end
  • Steering feels rough when turning
  • Noise worse in cold weather

How to Fix

Replace the front strut mount bearings. The mounts are typically replaced during strut replacement. Strut mount assemblies cost $30-60 each. If the struts are still in good condition, just the mount/bearing can be replaced using a spring compressor ($60-120 in parts). Complete strut assemblies with mounts pre-installed (quick struts) cost $120-200 each and are the easiest repair option. Labor: $200-400 for both sides.

What you need to fix it

Only diagnosis- and fitment-reviewed repair parts are linked here.

  • Genuine Nissan N17/E12 strut bearing 54325-1HA0A

    2012-2019 Versa sedan and 2014-2019 Versa Note 1.6L; quantity two. The 2012 C11 hatchback instead uses JE20C.

    NissanPartsDeal
  • Genuine Nissan N18 Versa strut bearing 54325-5FA0A

    Confirm VIN and quantity two.

    Nissan Parts & Accessories Online

As an Amazon Associate, we earn from qualifying purchases; other part links may also earn au7o a commission. Confirm fitment by VIN before buying.

Typical repair cost:$100 - $600

Research This Issue

GoogleRedditYouTubeNHTSA
Community Reported
Medium Confidence
Community reported
3,500 owners

On the 2012-2021 Nissan Versa, the 2012-2021 Versa CVT (Jatco JF015E) is one of the most failure-prone transmissions in Nissan's lineup. The combination of a budget vehicle with heavy use leads to premature CVT failure, often before 100,000 miles. Nissan extended the CVT warranty on 2012-2017 models to 10 years/120,000 miles due to a class-action settlement (Batista v. Nissan).

Common Symptoms

  • Shuddering and jerking during acceleration
  • Complete loss of drive
  • Transmission warning light
  • Whining or buzzing noise
  • Delayed engagement from stop
  • Vehicle won't move despite engine running

How to Fix

Check if covered by extended CVT warranty (10yr/120k for 2012-2017). Change CVT fluid every 30,000 miles with NS-3. Valve body replacement for shuddering ($1,200-2,000). Complete CVT replacement ($3,000-4,500). Consider manual transmission on earlier models if available.

What you need to fix it

Only diagnosis- and fitment-reviewed repair parts are linked here.

  • Genuine Nissan NS-2 CVT fluid quart 999MP-CSHNS2

    Confirm the owner manual/VIN; do not substitute NS-3 or mix fluids.

    Chapman Nissan Parts
  • Genuine Nissan NS-3 CVT fluid quart 999MP-CSHNS3

    2013-2017 Versa Sedan N17 and 2014-2017 Versa Note E12 CVT branch in this warranty group; confirm VIN/manual and fill procedure.

    Nissan Wholesale Direct

As an Amazon Associate, we earn from qualifying purchases; other part links may also earn au7o a commission. Confirm fitment by VIN before buying.

Typical repair cost:$300 - $4,500

Research This Issue

Based on 3,500 owner reports

GoogleRedditYouTubeNHTSA
Community Reported
High Confidence3,500 owner reportsLast reported by owners Feb 2026Reviewed Feb 2026

On the 2012-2014 Nissan Versa, early N17 Versa sedans have a documented pattern of master cylinder failure at surprisingly low mileage, with owners reporting the pedal slowly sinking toward the floor under steady pressure at a stoplight and requiring a pump-up to get firm stopping power. The failure is an internal one: the primary and secondary piston cup seals extrude or roll, so fluid bypasses inside the bore instead of being pushed to the wheels. Because it bypasses internally there is no puddle, the reservoir level barely moves, and the brake warning light typically never comes on — which is exactly why it gets misdiagnosed as air in the lines and chased through repeated bleeds. Cases have been reported on cars with under 20,000 miles where the dealer ultimately found the master cylinder leaking internally. A worn ABS actuator can produce an identical sinking pedal on higher-mileage cars, so the two need to be separated before parts are thrown at it.

Common Symptoms

  • Brake pedal slowly sinks to the floor at a stop
  • Pedal must be pumped to get firm braking
  • Spongy pedal that returns after bleeding then degrades again
  • No visible brake fluid leak and normal reservoir level
  • Brake warning light does not illuminate despite the fault

How to Fix

Diagnose before replacing. With the engine running and steady moderate pressure on the pedal, a pedal that creeps toward the floor over 15-30 seconds with no external leak is a bypassing master cylinder. To separate the master from the ABS unit, cap the master cylinder outlet ports: if the pedal is now rock-hard, the master is fine and the fault is downstream in the ABS actuator; if it still sinks, replace the master cylinder. Bleed strictly in the factory sequence afterward — bleeding a Versa out of order traps air in the ABS valve body and reproduces a spongy pedal that gets blamed on the new part. Flush old dark fluid entirely; degraded, moisture-laden fluid is what chews the seals in the first place. This is a stopping-power defect — do not defer it.

Typical repair cost:$250 - $700

Research This Issue

GoogleRedditYouTubeNHTSA
Community Reported
High ConfidenceVerifiedReviewed Aug 2026

On the 2007-2022 Nissan Versa, the Versa's NISSAN Advanced Air Bag System weighs the front passenger via an occupant classification sensor mat and bladder built into the passenger seat cushion, plus a seat-belt tension sensor. The pressure mat's printed circuit traces crack from repeated seat loading, and the harness that runs under the seat frame chafes or corrodes at the connector. When the OCS control unit sees an implausible or open-circuit reading it fails safe and leaves the 'PASSENGER AIR BAG OFF' telltale illuminated with a normal-sized adult seated — meaning the passenger front airbag will not deploy in a crash. Owners report the light behaving erratically first (going out only when the passenger shifts position) before staying on permanently. Nissan's service remedy is often a re-zero/reflash of the OCS control unit rather than parts, so a good number of cars are fixed without a seat teardown, but a genuinely failed mat requires the seat cushion assembly.

Common Symptoms

  • PASSENGER AIR BAG OFF light stays lit with an adult in the seat
  • Airbag warning light on in the instrument cluster
  • Passenger airbag status light flickers when passenger shifts weight
  • Light goes out only if the passenger sits in an unnatural position
  • Airbag system stores occupant-sensor fault codes

How to Fix

Do not clear it and ignore it. Have the airbag system scanned for OCS/occupant-sensor codes. First step is inspecting and reseating the connectors under the passenger seat for chafe, corrosion, or a pinched harness from cargo shoved under the seat. If wiring is sound, the dealer performs the OCS control-unit zero-point reset/reprogram, which resolves a large share of cases. If the sensor mat itself is open, the passenger seat cushion assembly with integrated OCS mat must be replaced and the system recalibrated. Bypassing or resistor-spoofing the sensor is discussed on forums but defeats a federally mandated restraint and should not be done.

Typical repair cost:$150 - $1,200

Research This Issue

GoogleRedditYouTubeNHTSA
Community Reported
Medium ConfidenceVerifiedReviewed Aug 2026

On the 2007-2023 Nissan Versa HR16DE, the 1.6L HR16DE uses a timing chain, not a belt, but Nissan pairs it with a hydraulically pressurized tensioner fed by a variable-displacement oil pump that produces low pressure at idle and low rpm. On a cold start the tensioner has bled down and the pump is not yet making pressure, so the chain goes slack on its departure from the crank sprocket and slaps the plastic guide — a two-to-five-second rattle or diesel-like clatter from the passenger side of the engine that disappears once oil pressure builds. Owners on the Versa forums document this from early C11 cars all the way through the N17 and into the third-generation N18, where it is still discussed. Left alone with extended oil-change intervals or thin/degraded oil, the guide face wears through, the chain stretches, and the cam timing drifts far enough to set variable-valve-timing codes and eventually risk a jumped tooth. The engine's twin-injector-per-cylinder port injection also produces a constant top-end tick that owners frequently confuse with the chain, so the two need to be told apart before spending money.

Common Symptoms

  • Rattling or clattering for a few seconds on cold start
  • Diesel-like noise from the front/passenger side of the engine
  • Noise disappears once oil pressure builds
  • Constant ticking from the top of the engine
  • Check engine light with cam/crank correlation codes in advanced cases

How to Fix

Distinguish the injector tick (constant, present hot, unchanged by rpm sweep) from the chain rattle (only on cold start, 2-5 seconds, then silent). For chain rattle: change the oil on a strict interval with the correct viscosity — several owners report the noise diminishing with a slightly heavier or full-synthetic oil because the tensioner holds pressure better. If the rattle grows longer, becomes present when warm, or VVT/timing correlation codes appear, replace the timing chain, both guides, and the hydraulic tensioner as a set, and inspect the oil pump pickup and screen for sludge that starved the tensioner in the first place. Do not just replace the tensioner on a stretched chain.

Typical repair cost:$700 - $1,800

Research This Issue

GoogleRedditYouTubeNHTSA
Community Reported
Low ConfidenceVerifiedReviewed Aug 2026

On the 2007-2019 Nissan Versa, a recurring Versa complaint across both the 1.6L HR16DE and the 1.8L MR18DE is oil disappearing with no drips on the driveway and no visible smoke. The two mechanisms owners and mechanics land on are oil-control ring coking — the low-tension rings carbon up in their grooves and stop scraping — and worn valve guides/stem seals letting oil down the intake ports at idle and on overrun. The MR18DE compounds this with a plated aluminum bore rather than iron liners; where the plating is imperfect the bore wears and consumption climbs early. Forum reports span the whole range from a mild 200 ml per 1,500 km on a high-mileage car (arguably normal) to genuinely defective cases burning a quart every 200 miles by 75,000 miles. The real danger is not the oil cost: the Versa has no low-oil-level warning, only a pressure light that comes on far too late, so owners who trust the change interval run the engine dangerously low and destroy bearings or seize the engine.

Common Symptoms

  • Oil level low between changes with no leak on the ground
  • Adding a quart of oil every 1,000-3,000 miles or worse
  • Blue smoke on cold start or on deceleration
  • Oil pressure warning light with no prior symptom
  • Fouled spark plugs
  • Catalytic converter efficiency code from oil ash

How to Fix

First establish the actual rate with a documented consumption test — mark the level, drive a measured 1,000 miles, remeasure. Rule out the cheap causes: valve cover gasket seeping onto the exhaust, PCV valve stuck open pulling oil into the intake, and a clogged PCV circuit pressurizing the crankcase. Blue smoke at start-up after sitting points at valve stem seals, which can be replaced with the head on using compressed air; blue smoke under load or on deceleration points at rings. Ring cleaning/decoking helps some engines; a genuinely worn plated bore on the 1.8L means an engine rebuild or a used engine, and most owners choose to simply monitor and top off. Regardless of the fix, check the dipstick every fuel fill — this engine will not warn you before it runs dry.

Typical repair cost:$200 - $4,500

Research This Issue

GoogleRedditYouTubeNHTSA
Community Reported
Medium ConfidenceVerifiedReviewed Aug 2026

On the 2007-2023 Nissan Versa, the transverse HR16DE/MR18DE drivetrain is carried on a soft mount set tuned to keep a small four-cylinder from buzzing the cabin. The passenger-side upper mount is a fluid-filled hydraulic design, and it is the one that goes first: the rubber splits, the damping fluid leaks out, and it collapses into a solid rubber block that transmits every combustion pulse straight into the body. The lower torque strut (the 'dogbone' link that reacts driveline torque) is the second common failure, and its bushings tear so the powertrain rocks fore-and-aft on throttle tip-in and lift-off. The tell-tale diagnostic that separates mounts from a real engine misfire is that the shake is worst in Drive with the brake held at a stop and improves the instant you shift to Neutral or raise the idle slightly — a genuine misfire does not care what gear you're in. Owners often chase rough-idle causes for months before someone points at the mounts.

Common Symptoms

  • Heavy vibration at idle in Drive with the brake applied
  • Vibration smooths out in Neutral or Park
  • Clunk or thud from the engine bay on acceleration and on lift-off
  • Steering wheel and seat shake at stoplights
  • Rattle from the front of the engine bay over bumps

How to Fix

Do the in-gear/neutral test at a stop: heavy vibration in Drive with the brake on that clears in Neutral or with a light throttle bump points at the passenger-side hydraulic mount. Have someone watch the engine while it is loaded against the brake in Drive and again in Reverse — excessive rocking or a visible clunk confirms it. Inspect the passenger-side hydraulic mount for a wet/oily residue, which is the leaked damping fluid. Replace the failed mount; if the car has high mileage, do the hydraulic mount and the lower torque strut together, since the strut bushings are almost always worn as well. Rule out ignition coils and vacuum leaks first, because those produce a similar idle roughness and are the existing known failure on this platform.

Typical repair cost:$180 - $600

Research This Issue

GoogleRedditYouTubeNHTSA
Community Reported
Medium ConfidenceVerifiedReviewed Aug 2026

On the 2007-2019 Nissan Versa HR16DE, the Versa HR16DE engine experiences ignition coil failure, typically one coil at a time. Failed coils cause misfires on the affected cylinder, resulting in rough running, loss of power, and increased emissions. The compact engine bay and heat soak contribute to coil degradation. Coils typically fail between 60,000-100,000 miles. Running on a failed coil can damage the catalytic converter from unburned fuel.

Common Symptoms

  • Engine misfire and rough idle
  • Check engine light flashing
  • Loss of power
  • Increased fuel consumption
  • Rough vibration at idle

How to Fix

Replace the failed ignition coil(s). It is recommended to replace all 4 coils along with spark plugs at the same time. OEM coils cost $40-60 each; aftermarket (Denso, NGK) cost $20-35 each. Total parts for all 4: $80-240. Labor: $80-150. This is a straightforward DIY job requiring only basic tools and 30 minutes.

What you need to fix it

Only diagnosis- and fitment-reviewed repair parts are linked here.

  • Genuine Nissan C11 Versa ignition coil 22448-1KT1A

    Confirm VIN.

    NissanPartsDeal
  • Genuine Nissan N17/E12 Versa ignition coil 22448-5RB0A

    2012-2019 Versa sedan and 2014-2019 Versa Note 1.6L HR16DE; confirm VIN/body.

    NissanPartsDeal
  • Genuine Nissan MR18DE spark plug 22401-JD01B

    Confirm VIN and plug specification.

    NissanPartsDeal
  • Genuine Nissan HR16DE spark plug 22401-1HC1B

    2012-2019 Versa sedan and 2014-2019 Versa Note 1.6L HR16DE; quantity four. Fitment/availability: Ships in 1-3 business days and add-to-cart live at review

    NissanPartsDeal

As an Amazon Associate, we earn from qualifying purchases; other part links may also earn au7o a commission. Confirm fitment by VIN before buying.

Typical repair cost:$80 - $400

Research This Issue

GoogleRedditYouTubeNHTSA
Community Reported
Medium Confidence

On the 2007-2024 Nissan Versa, each Versa door contains an integrated lock actuator with a small DC motor driving a nylon gear train. The gears strip or the motor's internal contacts wear, and the result is the classic signature owners describe: a loud buzzing, grinding, or rapid machine-gun clicking from inside the door skin when the lock button or key fob is pressed — the motor spinning freely with nothing to drive. This is a repeat offender on the platform, with owners reporting having to do several doors over the life of the car, and it worsens in cold climates where grease stiffens and the motor works harder. The genuinely bad outcome is when the actuator jams in the locked position: the door cannot be opened from inside or outside, and getting into a rear door that failed shut with a child seat in it is a real problem. The diagnostic split matters — a single door failing points at that door's actuator, while all doors or all windows failing at once points instead at the driver's master switch or the body control module.

Common Symptoms

  • Loud buzzing or grinding from inside the door when locking or unlocking
  • Rapid clicking from one door with no lock movement
  • One door will not lock or unlock with the fob or master switch
  • Door stuck shut and will not open from inside or outside
  • Locks cycle by themselves or only work intermittently in cold weather

How to Fix

Diagnose by scope: one door misbehaving means that door's lock actuator; all doors dead from the driver's switch while individual door switches still work means the master switch; nothing at all working means fuse, relay, or BCM. For a stripped actuator, replace the door lock actuator assembly — the door trim panel and vapor barrier come off, and the actuator unbolts from the latch. If the door is already jammed shut, the trim can usually be worked loose enough to reach the latch release rod through the access holes, or the latch reached through the door edge; forum threads document doing this on stuck Versa doors rather than cutting anything. Do not just lubricate a buzzing actuator — the gear teeth are already gone, and it will strand you.

Typical repair cost:$120 - $450

Research This Issue

GoogleRedditYouTubeNHTSA
Community Reported
High ConfidenceVerifiedReviewed Aug 2026

On the 2007-2019 Nissan Versa, the Versa's manual-climate HVAC uses a resistor pack (Nissan p/n 27150-EY00A on early cars) mounted in the air ducting next to the blower motor to drop voltage for the low and mid fan speeds; only the top speed bypasses it through a relay. The resistor element runs hot, and it runs hotter still once the cabin air filter clogs or the blower motor's brushes wear and start drawing extra current, so the low-speed elements open up. The classic signature is losing speeds 1, 2, and 3 while speed 4 still blasts. Because the resistor and the blower share the same failure driver, a resistor that burns out a second time usually means the blower motor itself is the root cause. The part sits on the left-hand side of the HVAC case and on most Versas the accelerator pedal assembly has to come out to reach it, which is why shop quotes look high for a sub-$25 part.

Common Symptoms

  • Blower fan works only on the highest speed setting
  • No air from vents on low or medium fan settings
  • Fan speeds cut out intermittently then return
  • Blower whine or noise before the resistor failed
  • No heat or A/C airflow at any speed if the blower also failed

How to Fix

Confirm the pattern: if only the highest fan speed works, replace the blower motor resistor pack. Replace the cabin air filter at the same time — a restricted filter is the most common reason the resistor cooked. If the resistor has failed once before, or if the blower was noisy/whining beforehand, replace the blower motor along with it, since a current-hungry motor will burn the new resistor out again. If no speeds work at all, check the blower fuse and blower relay first, not the resistor. Access on most Versas requires removing the accelerator pedal assembly to reach the resistor in the duct.

Typical repair cost:$60 - $350

Research This Issue

GoogleRedditYouTubeNHTSA
Community Reported
High ConfidenceVerifiedReviewed Aug 2026

On the 2007-2019 Nissan Versa, the Nissan Versa MAF sensor is prone to contamination and failure, particularly on the HR16DE 1.6L engine. The hot wire element becomes contaminated with oil vapors from the PCV system and dirt that passes through the air filter. This causes incorrect air flow readings, leading to poor engine performance, hesitation, and increased emissions. The issue often presents intermittently before becoming a constant problem.

Common Symptoms

  • Hesitation on acceleration
  • Rough idle
  • Poor fuel economy
  • Check engine light with P0101
  • Engine stalling

How to Fix

Clean the MAF sensor with CRC MAF Sensor Cleaner spray ($8-12). If cleaning does not resolve the issue, replace the MAF sensor. Aftermarket sensors cost $50-100; OEM Nissan sensors cost $120-200. The sensor is located in the air intake tube and takes 5-10 minutes to replace with basic tools. Ensure the air filter is clean and properly seated after MAF service.

What you need to fix it

Only diagnosis- and fitment-reviewed repair parts are linked here.

  • CRC 05110 Mass Air Flow Sensor Cleaner 11 oz

    Use only on the removed MAF element per label; do not use brake/carburetor cleaner or touch the element.

    AutoZone
  • Genuine Nissan early Versa MAF 22680-7S000

    2007-2019 Versa catalog range across HR16DE/MR18DE, but later production may use 5RB0A; VIN/production-date confirmation required.

    NissanPartsDeal
  • Genuine Nissan later Versa MAF 22680-5RB0A

    Confirm VIN because catalog overlap exists.

    NissanPartsDeal

As an Amazon Associate, we earn from qualifying purchases; other part links may also earn au7o a commission. Confirm fitment by VIN before buying.

Typical repair cost:$10 - $250

Research This Issue

GoogleRedditYouTubeNHTSA
Community Reported
Medium Confidence

STEERING:ELECTRIC POWER ASSIST SYSTEM

Nissan North America, Inc. (Nissan) is recalling certain 2021 Versa and Kicks vehicles. An intermittent electrical connection in the electric power steering (EPS) torque sensor can disable the power steering assist.

Campaign #22V69300015/09/2022

STEERING:ELECTRIC POWER ASSIST SYSTEM

Nissan North America, Inc. (Nissan) is recalling certain 2021 Versa and Kicks vehicles. An intermittent electrical connection in the electric power steering (EPS) torque sensor can disable the power steering assist.

Campaign #23V49600018/07/2023

Enter your VIN at NHTSA.gov to check recalls specific to your vehicle.

get a full repair guide

What is the 2012-2014 Nissan Versa Brake Master Cylinder Internal Seal Bypass — Pedal Sinks to the Floor With No External Leak?

Early N17 Versa sedans have a documented pattern of master cylinder failure at surprisingly low mileage, with owners reporting the pedal slowly sinking toward the floor under steady pressure at a stoplight and requiring a pump-up to get firm stopping power. The failure is an inte… Repairs typically run $250-$700. Severity: high.

What is the 2007-2022 Nissan Versa Passenger Occupant Classification Sensor (OCS) Mat Failure — Passenger Airbag Stays Disabled?

The Versa's NISSAN Advanced Air Bag System weighs the front passenger via an occupant classification sensor mat and bladder built into the passenger seat cushion, plus a seat-belt tension sensor. The pressure mat's printed circuit traces crack from repeated seat loading, and the… Repairs typically run $150-$1,200. Severity: high.

What is the 2007-2023 Nissan Versa HR16DE Timing Chain Tensioner Slack — Cold-Start Rattle and Chain Guide Wear?

The 1.6L HR16DE uses a timing chain, not a belt, but Nissan pairs it with a hydraulically pressurized tensioner fed by a variable-displacement oil pump that produces low pressure at idle and low rpm. On a cold start the tensioner has bled down and the pump is not yet making press… Repairs typically run $700-$1,800. Severity: medium.

What is the 2007-2024 Nissan Versa Rear Wheel Bearing Failure — Press-In Bearing on the Torsion-Beam Axle?

The Versa's rear suspension is a simple torsion beam with non-driven hubs, and on sedan and Versa Note models the rear bearing is a press-in double-row unit rather than a bolt-on hub cartridge. These are a well-documented wear item on the platform, typically surfacing between rou… Repairs typically run $180-$650. Severity: medium.

What is the 2007-2019 Nissan Versa Piston Ring and Valve Guide Oil Consumption — Quart Loss Between Changes With No External Leak?

A recurring Versa complaint across both the 1.6L HR16DE and the 1.8L MR18DE is oil disappearing with no drips on the driveway and no visible smoke. The two mechanisms owners and mechanics land on are oil-control ring coking — the low-tension rings carbon up in their grooves and s… Repairs typically run $200-$4,500. Severity: medium.

What is the 2007-2023 Nissan Versa Collapsed Hydraulic Engine Mount and Torque Strut — Idle Shake and Clunk on Acceleration?

The transverse HR16DE/MR18DE drivetrain is carried on a soft mount set tuned to keep a small four-cylinder from buzzing the cabin. The passenger-side upper mount is a fluid-filled hydraulic design, and it is the one that goes first: the rubber splits, the damping fluid leaks out,… Repairs typically run $180-$600. Severity: medium.

What is the 2007-2024 Nissan Versa Door Lock Actuator Gear Stripping — Buzzing Door and Door Stuck Shut?

Each Versa door contains an integrated lock actuator with a small DC motor driving a nylon gear train. The gears strip or the motor's internal contacts wear, and the result is the classic signature owners describe: a loud buzzing, grinding, or rapid machine-gun clicking from insi… Repairs typically run $120-$450. Severity: medium.

What is the 2007-2019 Nissan Versa Ignition Coil Failure?

The Versa HR16DE engine experiences ignition coil failure, typically one coil at a time. Failed coils cause misfires on the affected cylinder, resulting in rough running, loss of power, and increased emissions. The compact engine bay and heat soak contribute to coil degradation. Repairs typically run $80-$400. Severity: medium.

What is the 2012-2022 Nissan Versa Front Strut Mount Bearing Noise?

The second and third generation Versa develops noise from the front strut mount bearings, producing a creaking, popping, or groaning sound when turning the steering wheel, especially at low speeds and in parking lots. The strut mount bearing (also called a strut plate bearing) we… Repairs typically run $100-$600. Severity: low.

What is the 2007-2019 Nissan Versa HVAC Blower Motor Resistor Pack Burnout — Fan Works Only on High?

The Versa's manual-climate HVAC uses a resistor pack (Nissan p/n 27150-EY00A on early cars) mounted in the air ducting next to the blower motor to drop voltage for the low and mid fan speeds; only the top speed bypasses it through a relay. The resistor element runs hot, and it ru… Repairs typically run $60-$350. Severity: low.

What is the 2007-2019 Nissan Versa Mass Air Flow Sensor Failure?

The Nissan Versa MAF sensor is prone to contamination and failure, particularly on the HR16DE 1.6L engine. The hot wire element becomes contaminated with oil vapors from the PCV system and dirt that passes through the air filter. This causes incorrect air flow readings, leading t… Repairs typically run $10-$250. Severity: low.