Au7o mascotAu7o
Known IssuesTest Hub demo
  1. Au7o
  2. /
  3. Known Issues
  4. /
  5. Mazda
  6. /
  7. Tribute
Mazda · Known Issues

2001-2011 Mazda Tribute Problems: 17 Known Issues

2001-2011 model years · 730+ owner reports · Updated September 2026

Share:@au7o.io

All years · All trims · All engines

Choose the year and equipment for your written issues and visual request.

No email neededHow interest is saved

Interest applies to the selected vehicle and configuration; it is not a reservation. Voting stores a first-party identifier for up to 180 days to prevent repeat votes. No account or email is needed. Clearing cookies or using another device may count separately. Privacy

Choose a year to request this visual. Trim and engine are optional; omitted trim is Not specified.

Known IssuesMotorcycle IssuesDTC LookupDrivePricingAboutTermsPrivacyCookiesConsentData rightsCopyrightFeedback
Share:@au7o.io

Vehicle data and repair guidance on this site are compiled with AI assistance and may contain errors. Always verify with your service manual or a qualified mechanic.

Data protection representation

DataRep representative in the United KingdomDataRep representative in the European Union
Au7o · 2026
Built for DIY mechanics. Privacy-first.
Explore free Hub demo

Visual coming soon

Your interest helps us choose what to build next.

Visual Known Issues · Coming soon

$4.99/month plus taxes at launch · No payment today

Preview the XT6 example

Choose your vehicle configuration

Choose a year to request this visual. Trim and engine are optional; omitted trim is Not specified.

Which vehicle’s visual would you like?

Choose from our year, make, model and trim catalog. This does not change the page underneath or mean a visual is already available.

Choose a vehicle configuration to continue. No request has been submitted.

Optional email notification

Choose a year to request this visual. Trim and engine are optional; omitted trim is Not specified.

Which vehicle’s visual would you like?

Choose from our year, make, model and trim catalog. This does not change the page underneath or mean a visual is already available.

Choose a vehicle configuration to continue. No request has been submitted.

Issue summary

According to Au7o's analysis of 730+ owner reports, the 2001-2011 Mazda Tribute has 17 documented known issues, with 9 rated critical. The most serious are CD4E Transmission Failure ($1,500-$3,500 repair), 3.0L Duratec Timing Chain Tensioner and Guide Wear Causing Cold-Start Rattle ($900-$1,800 repair), Rear Subframe Corrosion and Control Arm Bushing Failure ($200-$2,000 repair), Brake Master Cylinder Reservoir Cap Leaks Onto ABS Module Connector, Causing Melting and Fire (Recall 12V016) ($0-$0 repair), PCM Calibration Causes Engine Stall During Deceleration Below 40 mph (Recall 04V175) ($0-$0 repair), Speed Control Cable Connector Contacts Engine Cover, Causing Stuck Throttle (Recall 12V357) ($0-$0 repair), Fuel Delivery Module Flange Cracks and Leaks Fuel (Recall 16V788, 2010-2011 3.0L) ($0-$900 repair), Rear Wheel Well and Shock Mount Area Rusts Through Into the Cabin ($300-$1,800 repair) and Electric Power Steering Torque Sensor Fault Drops Steering Assist (Recall 14V282) ($0-$1,800 repair). The most commonly reported issue is CD4E Transmission Failure with 350 owner reports. Across all issues with published estimates, repair costs range from $40 to $3,500. DIY maintenance guides at au7o.io.

In This Article

  • Tribute Engine3
  • Tribute Suspension2
  • Tribute Body/Panels2
  • Tribute Transmission1
  • Tribute Brakes1
  • Tribute Safety/Recalls1
  • Tribute Fuel System1
  • Tribute Steering1
  • Tribute Drivetrain2
  • Tribute Exterior1
  • Tribute Emissions1
  • Tribute HVAC1
  • Recalls6
  • FAQ
Get Started
Back to top

In This Article

  • Engine3
  • Suspension2
  • Body/Panels2
  • Transmission1
  • Brakes1
  • Safety/Recalls1
  • Fuel System1
  • Steering1
  • Drivetrain2
  • Exterior1
  • Emissions1
  • HVAC1
  • Recalls6
  • FAQ

All 17 Known Issues

NHTSA Recalls6 recalls

FUEL SYSTEM, GASOLINE:DELIVERY:FUEL PUMP

Mazda North American Operations (Mazda) is recalling certain model year 2010-2011 Tribute vehicles manufactured March 3, 2009, to May 26, 2011. On vehicles with a 3.0L engine, the Fuel Delivery Module (FDM) may crack, causing a fuel leak.

Campaign #16V78800028/10/2016

SUSPENSION:FRONT:WHEEL BEARING

The Timken Company (Timken) is recalling certain aftermarket front wheel bearings, part number 510072, sold from January 22, 2015, to May 21, 2015, to be used as service parts on 2001-2012 Ford Escape, 2001-2011 Mazda Tribute, and 2005-2011 Mercury Mariner vehicles. The affected wheel bearings have incorrect dimensions of a 42mm bore, 76mm outer dimension, and 39mm width, instead of a 42mm bore, 78mm outer dimension and a 45mm width.

Campaign #15E04500003/06/2015

STEERING:ELECTRIC POWER ASSIST SYSTEM

Mazda North American Operations (Mazda) is recalling certain model year 2008-2011 Tribute vehicles manufactured October 5, 2006, through September 11, 2010. The affected vehicles have a steering torque sensor that may not be able to properly detect driver steering input. As a result, the system could remove the Electric Power Steering (EPS) assist.

🔧
A mechanic who knows YOUR exact car
Answers tuned to your year, make, model & trim — not generic advice. Save your garage so it always has the right context.
Get ahead of Mazda Tribute problems — free
Leave your email and we'll alert you the moment there's a new recall or known issue for your Mazda Tribute. Free, no account needed.

Don't see your problem? Describe your symptoms to get a diagnosis, or .

Other Mazda Models

Mazda CX-530Mazda CX-6027Mazda CX-5026Mazda MX-5 Miata22Mazda MX-621Mazda Mazda319

Frequently Asked Questions

What are the most common Mazda Tribute problems?

According to Au7o's analysis of 730+ owner reports, the 2001-2011 Mazda Tribute has 17 documented issues. The most frequently reported are: CD4E Transmission Failure, 3.0L Duratec Timing Chain Tensioner and Guide Wear Causing Cold-Start Rattle, Rear Subframe Corrosion and Control Arm Bushing Failure. Of these, 9 are rated critical and should be addressed promptly.

Is the Mazda Tribute reliable?

The 2001-2011 Mazda Tribute has 17 known issues documented across 730+ owner reports. 9 issues are rated critical: CD4E Transmission Failure and 3.0L Duratec Timing Chain Tensioner and Guide Wear Causing Cold-Start Rattle and Rear Subframe Corrosion and Control Arm Bushing Failure and Brake Master Cylinder Reservoir Cap Leaks Onto ABS Module Connector, Causing Melting and Fire (Recall 12V016) and PCM Calibration Causes Engine Stall During Deceleration Below 40 mph (Recall 04V175) and Speed Control Cable Connector Contacts Engine Cover, Causing Stuck Throttle (Recall 12V357) and Fuel Delivery Module Flange Cracks and Leaks Fuel (Recall 16V788, 2010-2011 3.0L) and Rear Wheel Well and Shock Mount Area Rusts Through Into the Cabin and Electric Power Steering Torque Sensor Fault Drops Steering Assist (Recall 14V282). Prospective buyers should inspect for these issues and factor potential repair costs into their purchase decision. Regular maintenance following the manufacturer's schedule helps prevent many common problems.

How much does it cost to fix common Mazda Tribute problems?

Repair costs for known Mazda Tribute issues range from $0 to $3,500, depending on the specific problem and whether you choose DIY or professional repair. The most critical issue, CD4E Transmission Failure, typically costs $1,500-$3,500 to repair. Au7o provides step-by-step DIY maintenance guides that can help reduce repair costs.

What year Mazda Tribute is the most reliable?

Reliability varies across model years of the Mazda Tribute. Based on documented issues, problems are most commonly reported in earlier model years. Au7o recommends checking the specific known issues for your target year before purchasing, and having a pre-purchase inspection performed by a qualified mechanic. Our known issues database covers the 2001-2011 Mazda Tribute with 17 documented issues documented across 730+ owner reports.

Content on this page was compiled with AI assistance using NHTSA complaints, TSBs, owner reports, and public automotive data. While we strive for accuracy, this information may contain errors. Always verify repair procedures and specifications with your vehicle's service manual or a qualified mechanic.

Data sourced from 730+ owner reports, NHTSA recalls, TSBs, and automotive forums.

Filter:
ALL YEARS20112010200920082007200620052004200320022001

The 3.0L Duratec V6 uses two timing chains, one per cylinder head, each with a hydraulic tensioner and plastic guide rails. The tensioners bleed down when the engine sits, so the classic first symptom is a rattle or slap from the front of the engine for the first one to thirty seconds after a cold start, fading as oil pressure builds and re-extends the tensioner. Worn guides, a tensioner that no longer holds pressure, or a stretched chain let that slack persist, and because the 3.0L Duratec is an interference design, a chain that jumps time can put valves into pistons. Neglected oil changes accelerate this: sludge starves the tensioners and wears the guides. This is engine-code specific - it does not apply to the 2.0L Zetec, 2.3L or 2.5L four-cylinder Tributes, which use different valvetrain drive designs and failure modes.

Common Symptoms

  • Rattle or slap from the front of the engine for a few seconds after a cold start
  • Rough idle
  • Reduced power
  • Check engine light with camshaft/crankshaft correlation codes
  • Metallic debris found in the oil pan

How to Fix

First isolate accessory-drive tensioner noise from an internal timing rattle. For a confirmed 3.0L timing-drive fault, replace both chains, tensioners, guides and the front-cover sealing components as a complete repair; inspect oil pressure and sprockets while open.

What you need to fix it

Only diagnosis- and fitment-reviewed repair parts are linked here.

  • Cloyes 9-0708S complete timing-chain kit
    $205

    2001-2006 and 2008-2011 Mazda Tribute 3.0L V6 only. The direct listing includes two chains, tensioners, guides and crank sprocket; 2007 is not listed and front-cover gaskets/seals remain separate.

    PartsGeek

As an Amazon Associate, we earn from qualifying purchases; other part links may also earn au7o a commission. Confirm fitment by VIN before buying.

Typical repair cost:$900 - $1,800

Research This Issue

GoogleRedditYouTubeNHTSA
Community Reported
Medium ConfidenceVerifiedReviewed Aug 2026

Early 3.0L V6 Tributes shipped with a powertrain control module calibration that can let the engine stall while decelerating at speeds below about 40 mph - typically coasting to a stop, exiting a highway, or lifting off in traffic. Because the stall happens while the vehicle is still rolling, the driver loses power assist for steering and brakes with no warning. NHTSA campaign 04V175000 (Mazda recall 1904D) covers roughly 106,000 vehicles. This is a software defect, not a fuel or ignition-hardware failure, and it is separate from later idle complaints caused by a dirty throttle body or failing idle air control. Only 3.0L Duratec V6 automatics are covered.

Common Symptoms

  • Engine stalls when slowing down or coasting below 40 mph
  • Stall on lift-off approaching a stop sign or off-ramp
  • Loss of power steering and power brake assist while still moving
  • Restarts normally after the stall

How to Fix

Free recall remedy: dealers reprogram the PCM with the corrected calibration. Verify by VIN at nhtsa.gov/recalls - many surviving Tributes were sold used and never had the flash applied. If the flash is already on file and the vehicle still stalls on deceleration, the cause is a separate one: a dirty throttle body/IAC passage, a vacuum leak, or a failing crankshaft position sensor.

Typical repair cost:$0 - $0

Research This Issue

GoogleRedditYouTubeNHTSA
Community Reported
High ConfidenceVerifiedReviewed Aug 2026
Community reported
200 owners

Ignition coil-on-plug coils fail causing misfires. Ford 3.0L Duratec V6 coils are prone to cracking and arcing. Usually fails one at a time.

Common Symptoms

  • Engine misfire
  • Check engine light flashing
  • Rough idle
  • Loss of power
  • Poor fuel economy

How to Fix

Replace failed ignition coil. Replace all 6 spark plugs when replacing any coil. Consider replacing all coils proactively if one fails.

What you need to fix it

Only diagnosis- and fitment-reviewed repair parts are linked here.

  • Genuine Mazda AJ09-18-100 direct ignition coil
    OEMMazda AJ09-18-100

    Individual OEM coil replacement after a 3.0L cylinder-specific ignition failure is confirmed Fitment/availability: The inspected direct OEM dealer page identifies AJ09-18-100 and its Tribute fitment through 2001-2010. Confirm VIN/engine …

    Walser Mazda Parts

As an Amazon Associate, we earn from qualifying purchases; other part links may also earn au7o a commission. Confirm fitment by VIN before buying.

Typical repair cost:$80 - $300

Research This Issue

Based on 200 owner reports

GoogleRedditYouTubeNHTSA
Community Reported
Low Confidence200 owner reportsLast reported by owners Mar 2026Reviewed Mar 2026

The Tribute's rear subframe corrodes severely in rust-belt states, and the rear lower control arm bushings deteriorate prematurely. The combination causes the rear alignment to shift, producing tire wear and a wandering feeling at highway speeds. Ford/Mazda issued a recall for rear subframe corrosion on some Escape/Tribute models. The control arm bushings also fail from age and heat.

This issue also affects: Ford Escape

Common Symptoms

  • Vehicle wanders at highway speeds
  • Inner rear tire wear
  • Clunking from rear over bumps
  • Rear end feels loose
  • Visible rust on rear subframe

How to Fix

Check for NHTSA recall 14V-440 regarding rear subframe corrosion. If covered, the dealer will inspect and either apply corrosion treatment or replace the subframe at no cost. If not covered, inspect the subframe for structural integrity. Replace rear control arm bushings if cracked or separated ($200-$400 per side). An alignment should follow any bushing or subframe work.

Find a Mazda dealer

Choose to share your location for this search, or enter an area below. Your search location is sent to Google to find dealers.

Open Mazda dealer map in Google Maps ↗

Call to confirm they service Mazda vehicles and check your VIN, recall eligibility, parts availability, and appointment options.

Owner tips & cautions

  • TipCheck NHTSA.gov for the recall on rear subframe corrosion — it covers many Tribute/Escape models even at high mileage. Free subframe replacement if your VIN is covered. Well worth a 2-minute check.
Typical repair cost:$200 - $2,000

Research This Issue

GoogleRedditYouTubeNHTSA
Community Reported
Medium Confidence

The Tribute's front wheel bearings are sealed units pressed into the steering knuckle rather than bolt-on hub assemblies, and they are a routine high-mileage failure across the whole run. The noise is a rumble or growl that starts around 15 mph, rises with road speed, and changes with cornering load - louder turning one way, quieter the other. Owners and shops on the Escape/Tribute forums treat these as a known platform weak point; several report replacing one side only to have the growl continue, because the opposite side was already going or the noise was actually tire wear. Ignored, a failing bearing produces play at the wheel and ABS wheel-speed faults. A separate 2015 aftermarket recall, NHTSA 15E045000, covered incorrectly dimensioned replacement front wheel bearings sold for these vehicles, which is a reason to fit a reputable brand rather than the cheapest listing.

Common Symptoms

  • Rumbling or growling noise that starts around 15 mph and rises with speed
  • Noise changes when swerving left versus right
  • Humming often mistaken for tire noise
  • Play at the wheel when rocked at 12 and 6 o'clock
  • ABS light with a wheel speed sensor code

How to Fix

Road-test and isolate the growl to a front corner, then inspect the tire, brake, axle and suspension before condemning the bearing. The bearing is pressed into the knuckle; installation still requires a press, retaining hardware as applicable and an alignment check.

What you need to fix it

Only diagnosis- and fitment-reviewed repair parts are linked here.

  • Timken 510072 front wheel bearing
    $42

    The retailer lists both FWD and 4WD branches, with narrower early-year fitment notes; confirm VIN/drivetrain and order one bearing per confirmed failed side.

    PartsGeek

As an Amazon Associate, we earn from qualifying purchases; other part links may also earn au7o a commission. Confirm fitment by VIN before buying.

Typical repair cost:$250 - $500

Research This Issue

GoogleRedditYouTubeNHTSA
Community Reported
Low ConfidenceVerifiedReviewed Aug 2026

First-generation Tributes in salt states rust through the rear inner wheel well and the sheet metal around the rear shock upper mount. NHTSA complaints and CarComplaints show a heavy cluster on the 2005 model year - 27 complaints for 'wheel well area completely rusted out' plus a separate cluster of premature rear strut/shock rust - and owners consistently report the right rear well going first, with the left following on some vehicles. The failure announces itself as a sudden loud clanking or pounding from the rear as the shock mount loses its support, and in the worst reported cases the suspension pushes up through the floor into the cargo area. The wheel-well sheet metal is thin and the corrosion develops behind intact-looking undercoating, so nothing is visible until the metal is gone. Owners specifically note that earlier model years received corrosion attention while 2005 did not. This is body-panel and shock-mount corrosion and is distinct from frame or subframe corrosion campaigns.

Common Symptoms

  • Loud clanking or pounding from the rear wheel area over bumps
  • Visible hole or perforation in the rear inner wheel well
  • Rust flaking around the rear shock upper mount
  • Rear suspension protruding into the cargo area
  • Water or road spray entering the cabin from the rear well

How to Fix

Inspect the inner and outer wheelhouse, shock-mount structure and surrounding floor before deciding whether the shell is safely repairable. This is cut-out, fabricated-metal and welding work; a generic patch or shock component is not a complete structural repair.

Typical repair cost:$300 - $1,800

Research This Issue

GoogleRedditYouTubeNHTSA
Community Reported
Medium ConfidenceVerifiedReviewed Aug 2026

The rear liftgate latching system on 2004-2005 Tributes - and on 2001-2003 Tributes that had liftgate components replaced in service with the 2004-equivalent parts - does not meet the inertia load requirement of FMVSS 206 ('Door Locks and Door Retention Components') in one direction. If the liftgate is left unlocked, crash forces can move the release rod and let the liftgate open, which risks ejection of cargo or occupants. NHTSA campaign 04V605000 covers about 49,800 vehicles. Note the unusual scope: it follows the parts, so an early Tribute that had liftgate work done at a dealer can be affected even though its build year is outside 2004-2005.

Common Symptoms

  • Liftgate pops open over bumps or in a collision
  • Loose or sloppy liftgate handle feel
  • Liftgate does not latch securely on the first close

How to Fix

Free recall remedy: dealers replace the rear liftgate latch release rod, the release rod attachment clip, and the door handle return spring. The campaign began January 2005. Check the VIN at nhtsa.gov/recalls; if the vehicle has had any liftgate latch or handle service history, ask the dealer to confirm which part revision is installed. Keeping the liftgate locked while driving mitigates the risk but is not a substitute for the repair.

Typical repair cost:$0 - $0

Research This Issue

GoogleRedditYouTubeNHTSA
Community Reported
High ConfidenceVerifiedReviewed Aug 2026
Community reported
350 owners

Same CD4E automatic transmission as the Ford Escape, prone to premature failure. Internal clutch and servo bore wear. V6 models with CD4E are most affected.

Common Symptoms

  • Harsh 1-2 shift
  • Slipping in 3rd and 4th gear
  • Shudder on acceleration
  • Delayed engagement
  • Burning trans fluid smell

How to Fix

Rebuild or replace transmission with remanufactured unit. Use updated servo bore kit during rebuild. Fluid changes every 30k miles help but do not prevent failure.

Owner tips & cautions

  • TipThe 4-cylinder model uses a different (more reliable) transmission — CD4E problems are V6 specific
Typical repair cost:$1,500 - $3,500

Research This Issue

Based on 350 owner reports

GoogleRedditYouTubeNHTSA
Community Reported
Low Confidence350 owner reportsLast reported by owners Mar 2026Reviewed Mar 2026

On 2001-2002 Tributes built April 20, 2000 through July 19, 2002, the brake master cylinder reservoir cap can allow brake fluid to weep out. The fluid runs down and reaches the ABS module wiring harness connector, where it promotes corrosion and a high-resistance short. NHTSA describes the outcome as corrosion in the electrical connector 'leading melting, smoking or possible fire' - owners were told to park the vehicle outside until repaired. This is a genuine underhood fire risk that has produced burning-odor and smoke complaints on the twin Ford Escape as well. A related earlier campaign, 07V157000, addressed the ABS module wiring harness on the same generation. Do not confuse this with the ABS pump/module electrical failures that simply set an ABS warning lamp.

Common Symptoms

  • Burning smell from under the hood
  • Smoke from the ABS module area on the driver's side
  • Brake fluid residue around the master cylinder cap and reservoir
  • ABS warning light on
  • Melted or corroded ABS harness connector

How to Fix

Free recall remedy under NHTSA 12V016000 (Mazda campaign 6712A): dealers replace the brake master cylinder reservoir cap and modify the ABS electrical circuit (harness/connector protection). Check the VIN at nhtsa.gov/recalls. If the repair was never done, inspect the reservoir cap area and the ABS connector for wet or crusted fluid and discoloration; a melted connector or module requires replacement outside the recall. Park outside until the recall work is completed.

Typical repair cost:$0 - $0

Research This Issue

GoogleRedditYouTubeNHTSA
Community Reported
High ConfidenceVerifiedReviewed Aug 2026

On 3.0L V6 Tributes equipped with speed control, there is inadequate clearance between the engine cover and the speed control (cruise) cable connector. When the accelerator pedal is pressed fully or nearly fully, the cable connector can catch on the engine cover and hold the throttle open after the driver lifts off. The condition occurs whether or not cruise control is switched on, because the mechanical interference is with the cable itself, not the cruise electronics. NHTSA campaign 12V357000 (Mazda recall 6812G) covers roughly 217,500 Tributes built across 2001-2006 and 2008 with the 3.0L Duratec. This is the Mazda twin of the same defect recalled on the Ford Escape. Four-cylinder Tributes are not covered by this campaign.

Common Symptoms

  • Throttle stays open after releasing the accelerator
  • Engine revs high and vehicle keeps accelerating
  • Sticking or hanging accelerator pedal after a full-throttle application
  • Difficulty slowing or stopping the vehicle

How to Fix

Free recall remedy: dealers increase the clearance at the engine cover so the speed control cable connector cannot bind. As an interim measure before parts were available, dealers disconnected and secured the speed control cable away from the throttle linkage (disabling cruise control until the permanent repair). Check the VIN at nhtsa.gov/recalls - the repair is still free and unexpired. If the pedal has ever hung up, do not defer this; drivers should know to shift to neutral and brake if the throttle sticks.

Typical repair cost:$0 - $0

Research This Issue

GoogleRedditYouTubeNHTSA
Community Reported
High ConfidenceVerifiedReviewed Aug 2026

On the final 2010-2011 Tributes built March 3, 2009 through May 26, 2011 with the 3.0L engine, the Fuel Delivery Module - the in-tank pump/sender assembly and its flange - can crack at the fuel supply port. The crack allows raw fuel to leak at the top of the tank, which is a fire risk with any ignition source and typically shows up first as a strong fuel smell at the rear of the vehicle or a wet spot under the tank after a fill-up. NHTSA campaign 16V788000 (Mazda campaign 0416J) covers this. It is small in volume - about 905 owners were notified when parts arrived - because it applies only to the last two model years with that engine; four-cylinder 2.5L Tributes are not covered.

Common Symptoms

  • Strong raw fuel smell, especially after filling the tank
  • Visible fuel leak or wet area near the top of the fuel tank
  • Fuel odor inside the cabin
  • Fuel stains on the driveway under the rear of the vehicle

How to Fix

Free recall remedy: dealers replace the FDM flange with a redesigned part having a revised fuel supply port. Interim owner letters went out December 23, 2016 and the parts-available notice on January 31, 2018, so plenty were never completed - check the VIN at nhtsa.gov/recalls. Outside the recall, a cracked FDM flange means dropping the tank and replacing the module, typically $500-$900 including labor. Do not drive a vehicle with an active fuel smell.

Typical repair cost:$0 - $900

Research This Issue

GoogleRedditYouTubeNHTSA
Community Reported
High ConfidenceVerifiedReviewed Aug 2026

The second-generation Tribute (2008-2011, built October 5, 2006 through September 11, 2010) uses electric power steering rather than a hydraulic pump. A software issue affecting operation of the steering torque sensor means the system may fail to correctly read driver input and, as a fail-safe, cuts EPS assist entirely. The wheel goes heavy without warning, which matters most in parking lots, tight turns and low-speed maneuvers where the assist is doing the most work. NHTSA campaign 14V282000 (Mazda campaign 7614E) covers roughly 33,000 vehicles. This is specific to the EPS-equipped second generation; 2001-2007 Tributes have a hydraulic rack and a different set of steering complaints.

Common Symptoms

  • Steering suddenly becomes very heavy at low speed
  • Power steering warning light or wrench light illuminates
  • Assist returns after an ignition cycle
  • Intermittent loss of assist while parking or turning into a driveway

How to Fix

Free recall remedy: dealers reprogram the power steering control module and the instrument cluster module, and replace EPS components at no charge if fault codes are found at inspection. The recall began in July 2014 - check the VIN at nhtsa.gov/recalls, since many of these changed hands before it was announced. If assist is still dropping after the reflash, the torque sensor or the EPS rack assembly itself is failing and is a $900-$1,800 repair outside the campaign.

Typical repair cost:$0 - $1,800

Research This Issue

GoogleRedditYouTubeNHTSA
Community Reported
High ConfidenceVerifiedReviewed Aug 2026
Community reported
180 owners

AWD models develop rear differential vibration and whining noise. PTU (power transfer unit) fluid breaks down causing bearing wear. Often misdiagnosed as wheel bearing.

Common Symptoms

  • Whining noise from rear at highway speed
  • Vibration at 50-70 mph
  • Growling noise that changes with speed
  • AWD system warning
  • Noise changes when coasting vs accelerating

How to Fix

Change PTU and rear differential fluid. If bearings are damaged, rebuild or replace differential. Fluid change every 30k miles prevents this.

What you need to fix it

Only diagnosis- and fitment-reviewed repair parts are linked here.

  • Motorcraft XY-75W140-QL SAE 75W-140 synthetic gear lubricant
    OEMMotorcraft XY-75W140-QL

    Owner-manual-specified lubricant branch for the Tribute AWD/4WD PTU Fitment/availability: The direct retailer page identifies Motorcraft XY-75W140-QL, one quart, meeting WSL-M2C192-A and API GL-5; it showed $40.09 and In Stock. Use only …

    XDP
  • Genuine Mazda 0000-77-80W9-QT SAE 80W-90 rear differential oil
    OEMMazda 0000-77-80W9-QT

    Owner-manual-specified lubricant branch for the Tribute AWD/4WD rear axle Fitment/availability: The direct authorized-dealer product page identifies genuine Mazda 0000-77-80W9-QT SAE 80W-90 rear differential oil, showed $11.40 and Add to…

    MazdaStuff

As an Amazon Associate, we earn from qualifying purchases; other part links may also earn au7o a commission. Confirm fitment by VIN before buying.

Owner tips & cautions

  • TipChange PTU fluid every 30k miles — Ford/Mazda does not list it as a service item but it prevents expensive failures
Typical repair cost:$200 - $1,200

Research This Issue

Based on 180 owner reports

GoogleRedditYouTubeNHTSA
Community Reported
Low Confidence180 owner reportsLast reported by owners Mar 2026Reviewed Mar 2026

AWD-equipped Tribute models develop leaks from the transfer case output shaft seal, dripping fluid onto the exhaust crossover pipe. The leak creates a burning smell and can cause the transfer case to run low on fluid, leading to bearing damage and eventual failure. The seal degrades from heat exposure and mileage, typically failing between 60,000-100,000 miles.

This issue also affects: Ford Escape

Common Symptoms

  • Burning smell from under vehicle
  • Fluid dripping from center of vehicle
  • Grinding noise from center of vehicle during turns
  • AWD system malfunction warning
  • Low transfer case fluid level

How to Fix

Replace the transfer case output seal ($15-$30 for the seal). The repair requires raising the vehicle and removing the rear driveshaft to access the seal. Refill the transfer case with the correct fluid (Motorcraft XY-75W140-QL or equivalent). If the seal has been leaking long enough to damage the transfer case bearings, a rebuilt unit ($600-$1,000) may be needed. Check fluid level every oil change.

What you need to fix it

Only diagnosis- and fitment-reviewed repair parts are linked here.

  • National 710971 PTU rear output shaft seal
    OEMNational 710971

    Rear-driveshaft output seal after leak location is confirmed on the verified early AWD branch Fitment/availability: The direct product page identifies National 710971 as a transfer-case output shaft seal and specifically lists 2001-2009 …

    FinditParts
  • Motorcraft XY-75W140-QL SAE 75W-140 synthetic gear lubricant
    OEMMotorcraft XY-75W140-QL

    Correct PTU refill lubricant after leak repair Fitment/availability: The direct retailer page identifies one quart of Motorcraft XY-75W140-QL meeting WSL-M2C192-A and API GL-5, showed $40.09 and In Stock. Fill only to the exact model-yea…

    XDP

As an Amazon Associate, we earn from qualifying purchases; other part links may also earn au7o a commission. Confirm fitment by VIN before buying.

Owner tips & cautions

  • TipThe Tribute is a Ford Escape underneath — all Escape transfer case repair guides apply. The output seal is a $20 part and 1-hour job. Don't let it leak until the transfer case runs dry and destroys itself.
Typical repair cost:$100 - $1,000

Research This Issue

GoogleRedditYouTubeNHTSA
Community Reported
Medium Confidence

Second-generation Tributes have a flip-up rear liftgate glass carried on two small hinges bonded and bolted at the top of the glass. The hinge bodies crack and the outer half breaks away, usually one side first. Once one hinge fails the glass hangs on a single point and can bind, refuse to latch, or - if forced open or slammed - break outright, turning a hinge replacement into a glass replacement. The parts are shared with the 2008-2012 Ford Escape and 2008-2011 Mercury Mariner; the Mazda hinge part numbers are ZZC1622B0 (right) and ZZC2622B0 (left), equivalent to Ford 8L8Z-78420A68-C/D. Forum consensus on the Escape/Tribute community is to replace at the first sign of a crack rather than wait.

Common Symptoms

  • Rear liftgate glass will not open or will not latch
  • Visible crack in the hinge at the top of the rear glass
  • Piece of the hinge has fallen off
  • Glass sits crooked or rattles when closed

How to Fix

Support and remove the liftgate glass, replace both cracked hinges as a pair, transfer or replace the seals as needed and align the glass before tightening. Stop using the glass hatch if either hinge is separating.

What you need to fix it

Only diagnosis- and fitment-reviewed repair parts are linked here.

  • Rear liftgate-glass left/right hinge set, OE interchange 8L8Z-78420A68-C/D
    $27

    The live listing supplies both sides; confirm the hinge shape and OE numbers against the vehicle before purchase.

    eBay

As an Amazon Associate, we earn from qualifying purchases; other part links may also earn au7o a commission. Confirm fitment by VIN before buying.

Typical repair cost:$60 - $350

Research This Issue

GoogleRedditYouTubeNHTSA
Community Reported
Medium ConfidenceVerifiedReviewed Aug 2026

The 3.0L Tribute uses a differential pressure feedback EGR (DPFE) sensor plumbed to the EGR tube by two short rubber hoses. The sensor's internal element degrades and the hoses crack or fall off, so the PCM sees no measurable flow and sets P0401 (insufficient EGR flow); a stuck or electrically failed EGR vacuum regulator solenoid sets P0403, and a carbon-plugged EGR passage in the intake sets P0401/P0402 as well. This is an emissions-inspection failure item on a large share of surviving Tributes. The common shop error is condemning the EGR valve itself - technicians on Tribute and Escape threads repeatedly find the actual fault is the DPFE sensor, its rubber signal hoses, or carbon blocking the EGR port, and the replaced valve does not clear the code.

Common Symptoms

  • Check engine light
  • Failed emissions or state inspection
  • Rough idle or light surge
  • Occasional hesitation under light acceleration

How to Fix

Inspect both DPFE hoses for heat damage, verify the sensor signal and clean the EGR passages before replacing parts. The sensor design and calibration vary across the long year range, and an EGR valve or DPFE sensor will not repair blocked passages or a damaged hose, so no single product is approved.

Typical repair cost:$60 - $450

Research This Issue

GoogleRedditYouTubeNHTSA
Community Reported
Medium ConfidenceVerifiedReviewed Aug 2026

The HVAC blower speed resistor sits behind the glove box in the heater case and burns out across the whole 2001-2011 Tribute run, shared with the Ford Escape and Mercury Mariner. The signature is that fan speeds 1 through 3 go dead while the top speed still works, because the highest setting bypasses the resistor and feeds the motor directly. The root cause is often not the resistor itself: an aging blower motor with worn bushings draws excess current and cooks the resistor, so a resistor replaced alone frequently fails again within months. On 2005-2006 Tributes the HVAC control head is also a documented failure point and can produce similar fan-speed symptoms.

Common Symptoms

  • Fan blows only on the highest speed setting
  • Low and medium fan speeds do nothing
  • Intermittent fan operation that comes and goes over bumps
  • Burning smell from the passenger footwell vents
  • Melted resistor connector

How to Fix

Confirm the blower operates only on high, inspect the connector for heat damage and measure blower-motor current before installing a resistor. This resistor branch applies only to manual climate controls; automatic temperature control uses a different module.

What you need to fix it

Only diagnosis- and fitment-reviewed repair parts are linked here.

  • AM Autoparts AM-1801208271 blower-motor resistor
    $21

    2008-2011 Mazda Tribute with manual climate control only. Direct product replaces 3F2Z-18591-AA / ZZCA-61-815; it does not fit the automatic-temperature-control branch or cover 2001-2006 without separate verification.

    AM Autoparts

As an Amazon Associate, we earn from qualifying purchases; other part links may also earn au7o a commission. Confirm fitment by VIN before buying.

Typical repair cost:$40 - $300

Research This Issue

GoogleRedditYouTubeNHTSA
Community Reported
High ConfidenceVerifiedReviewed Aug 2026
Campaign #14V28200029/05/2014

POWER TRAIN:AUTOMATIC TRANSMISSION:GEAR POSITION INDICATION (PRNDL)

Mazda North American Operations (Mazda) is recalling certain model year 2008 Tribute vehicles manufactured February 9, 2007 to April 22, 2008. The affected vehicles have had their CD4E transmission replaced with remanufactured one that was rebuilt between June 11, 2015 through July 15, 2015. These service repair part transmissions have a shift lever bolt that may not be properly tightened. As a result, the shift control lever could disengage from the transmission without warning.

Campaign #15V67700019/10/2015

HYBRID PROPULSION SYSTEM

Mazda North American Operations (Mazda) is recalling certain model year 2008 Mazda Tribute Hybrid vehicles manufactured October 10, 2006, to May 23, 2008. The coolant pump for the hybrid system may fail, resulting in the hybrid electronics overheating.

Campaign #14V55200010/09/2014

+ 1 more recalls. Check all on NHTSA.gov

Enter your VIN at NHTSA.gov to check recalls specific to your vehicle.

get a full repair guide

What is the 2001-2008 Mazda Tribute CD4E Transmission Failure?

Same CD4E automatic transmission as the Ford Escape, prone to premature failure. Internal clutch and servo bore wear. V6 models with CD4E are most affected. Repairs typically run $1,500-$3,500. Severity: high.

What is the 2001-2011 Mazda Tribute 3.0L Duratec Timing Chain Tensioner and Guide Wear Causing Cold-Start Rattle?

The 3.0L Duratec V6 uses two timing chains, one per cylinder head, each with a hydraulic tensioner and plastic guide rails. The tensioners bleed down when the engine sits, so the classic first symptom is a rattle or slap from the front of the engine for the first one to thirty se… Repairs typically run $900-$1,800. Severity: high.

What is the 2001-2011 Mazda Tribute Rear Subframe Corrosion and Control Arm Bushing Failure?

The Tribute's rear subframe corrodes severely in rust-belt states, and the rear lower control arm bushings deteriorate prematurely. The combination causes the rear alignment to shift, producing tire wear and a wandering feeling at highway speeds. Ford/Mazda issued a recall for re… Repairs typically run $200-$2,000. Severity: high.

What is the 2001-2002 Mazda Tribute Brake Master Cylinder Reservoir Cap Leaks Onto ABS Module Connector, Causing Melting and Fire (Recall 12V016)?

On 2001-2002 Tributes built April 20, 2000 through July 19, 2002, the brake master cylinder reservoir cap can allow brake fluid to weep out. The fluid runs down and reaches the ABS module wiring harness connector, where it promotes corrosion and a high-resistance short. NHTSA des… Repairs typically run $0-$0. Severity: high.

What is the 2001-2003 Mazda Tribute PCM Calibration Causes Engine Stall During Deceleration Below 40 mph (Recall 04V175)?

Early 3.0L V6 Tributes shipped with a powertrain control module calibration that can let the engine stall while decelerating at speeds below about 40 mph - typically coasting to a stop, exiting a highway, or lifting off in traffic. Because the stall happens while the vehicle is s… Repairs typically run $0-$0. Severity: high.

What is the 2001-2008 Mazda Tribute Speed Control Cable Connector Contacts Engine Cover, Causing Stuck Throttle (Recall 12V357)?

On 3.0L V6 Tributes equipped with speed control, there is inadequate clearance between the engine cover and the speed control (cruise) cable connector. When the accelerator pedal is pressed fully or nearly fully, the cable connector can catch on the engine cover and hold the thro… Repairs typically run $0-$0. Severity: high.

What is the 2010-2011 Mazda Tribute Fuel Delivery Module Flange Cracks and Leaks Fuel (Recall 16V788, 2010-2011 3.0L)?

On the final 2010-2011 Tributes built March 3, 2009 through May 26, 2011 with the 3.0L engine, the Fuel Delivery Module - the in-tank pump/sender assembly and its flange - can crack at the fuel supply port. The crack allows raw fuel to leak at the top of the tank, which is a fire… Repairs typically run $0-$900. Severity: high.

What is the 2001-2007 Mazda Tribute Rear Wheel Well and Shock Mount Area Rusts Through Into the Cabin?

First-generation Tributes in salt states rust through the rear inner wheel well and the sheet metal around the rear shock upper mount. NHTSA complaints and CarComplaints show a heavy cluster on the 2005 model year - 27 complaints for 'wheel well area completely rusted out' plus a… Repairs typically run $300-$1,800. Severity: high.

What is the 2008-2011 Mazda Tribute Electric Power Steering Torque Sensor Fault Drops Steering Assist (Recall 14V282)?

The second-generation Tribute (2008-2011, built October 5, 2006 through September 11, 2010) uses electric power steering rather than a hydraulic pump. A software issue affecting operation of the steering torque sensor means the system may fail to correctly read driver input and,… Repairs typically run $0-$1,800. Severity: high.

What is the 2001-2011 Mazda Tribute Ignition Coil Failure and Misfires?

Ignition coil-on-plug coils fail causing misfires. Ford 3.0L Duratec V6 coils are prone to cracking and arcing. Usually fails one at a time. Repairs typically run $80-$300. Severity: medium.

What is the 2001-2011 Mazda Tribute Rear Differential Vibration and Noise?

AWD models develop rear differential vibration and whining noise. PTU (power transfer unit) fluid breaks down causing bearing wear. Often misdiagnosed as wheel bearing. Repairs typically run $200-$1,200. Severity: medium.

What is the 2001-2011 Mazda Tribute Transfer Case Output Seal Leak (AWD Models)?

AWD-equipped Tribute models develop leaks from the transfer case output shaft seal, dripping fluid onto the exhaust crossover pipe. The leak creates a burning smell and can cause the transfer case to run low on fluid, leading to bearing damage and eventual failure. The seal degra… Repairs typically run $100-$1,000. Severity: medium.

What is the 2001-2011 Mazda Tribute Front Wheel Hub Bearing Growl - Pressed-In Bearing Requires Knuckle Removal?

The Tribute's front wheel bearings are sealed units pressed into the steering knuckle rather than bolt-on hub assemblies, and they are a routine high-mileage failure across the whole run. The noise is a rumble or growl that starts around 15 mph, rises with road speed, and changes… Repairs typically run $250-$500. Severity: medium.

What is the 2001-2005 Mazda Tribute Rear Liftgate Latch Release Rod Fails FMVSS 206 Inertia Load, Liftgate Can Open in a Crash?

The rear liftgate latching system on 2004-2005 Tributes - and on 2001-2003 Tributes that had liftgate components replaced in service with the 2004-equivalent parts - does not meet the inertia load requirement of FMVSS 206 ('Door Locks and Door Retention Components') in one direct… Repairs typically run $0-$0. Severity: medium.

What is the 2008-2011 Mazda Tribute Rear Liftgate Glass Hinges Crack and Break (2008-2011)?

Second-generation Tributes have a flip-up rear liftgate glass carried on two small hinges bonded and bolted at the top of the glass. The hinge bodies crack and the outer half breaks away, usually one side first. Once one hinge fails the glass hangs on a single point and can bind,… Repairs typically run $60-$350. Severity: medium.

What is the 2001-2008 Mazda Tribute DPFE Sensor and Carboned EGR Passages Setting P0401 Insufficient EGR Flow?

The 3.0L Tribute uses a differential pressure feedback EGR (DPFE) sensor plumbed to the EGR tube by two short rubber hoses. The sensor's internal element degrades and the hoses crack or fall off, so the PCM sees no measurable flow and sets P0401 (insufficient EGR flow); a stuck o… Repairs typically run $60-$450. Severity: low.

What is the 2001-2011 Mazda Tribute Blower Motor Resistor Burns Out - Heater and A/C Fan Works Only on High?

The HVAC blower speed resistor sits behind the glove box in the heater case and burns out across the whole 2001-2011 Tribute run, shared with the Ford Escape and Mercury Mariner. The signature is that fan speeds 1 through 3 go dead while the top speed still works, because the hig… Repairs typically run $40-$300. Severity: low.